The welder is equipped with a MOSFET transistor. This technology represents the highest standards of performance combined with compact and lightweight design. The result is 93% efficiency! The welding current is very stable and thus ensures a perfect weld.

Powerful fans ensure an optimal removal of heat from the unit.

TIG/MIG and MAG welding require a protective gas. Inert gases, such as argon and helium, as well as active gases (for example carbon dioxide) and other mixtures can be used. The solenoid valve regulates the flow of gas. The valve is operated via a button on the torch.

On the back of every welding machine is a screw with an earthing mark. Before use, earth the unit via a cross-section cable, which must be at least 6 mm².

This unit can also be operated using a foot pedal.

This device works with a 3-phase connection (400 V +/- 10 %).

If welding with more than 200 A it is recommend that a cooler is used. The connections of the welding device and the cooler-lines are marked accordingly with colours.

A non-contact high-frequency ignition in TIG mode ensures a cleaner weld starting point.

This is the time taken from the moment of pressing the torch button to that of the electric arc igniting. During this process the solenoid valve opens and the released gas pushes the oxygen from the gas lines and in doing so, forms a protective atmosphere for the arc.

Value of the arc ignition output current. This current can be adjusted at will. For precision welding, it is recommended to start with reduced power, weld smoothly and eventually adjust the current accordingly.

The time taken by the output power to rise to that of the welding current’s value.

The time taken of the output welding current to lower to that of the terminal current.

The output current value before the end of the weld. Welding with the final current helps prevent a crater forming at the end of the weld.

The time after the weld is finished in which gas continues to flow from the torch; this cools the burner and protects the weld from oxidation.

This function reduces the heat to the material. It is primarily suitable for welding thin plates. If MIG welding is used, it is perfect for aluminium welding.

The frequency of impulses during pulse mode.

Relation of pulse duration to period duration.

The maximum value of the electric current while in pulse mode.

The current which maintains the arc while in pulse mode.

This is the percentage difference of the time between the positive and negative direction of the current during a welding period. This feature allows control of the width of the welding seam and the depth of penetration.

This is the percentage difference of the time between the positive and negative direction of the current during a welding period.

Start the weld by placing pressure on the torch button. Stop the process by releasing the button.

By pressing the torch button the solenoid valve opens. allowing the gas to flow in. The gas pre-flow ignites the arc at the pre-set current. Releasing the burner button initiates a rise in the current to that of the pre-set welding current. The welding process stops once you press the burner button again.

Through automatically boosting the tension at the ignition of the arc, this function facilitates the electrical arc ignition. After ignition, the unit automatically returns to the pre-set voltage.

The current value increases automatically when the arc is shorter.

This function helps to prevent overheating of the electrode by switching off the welding current when the electrode sticks to the material.

A welding method in which the arc is maintained through an electrical current supplied from a non-consumable electrode. The arc is protected from the access of air by an inert gas.

Electrode welding with a coated electrode.

Choose between the 2T and 4T mode.

TIG welding is divided into AC (alternating current) and DC (direct current) welding.

Used to switch the pulse function on and off.

By using the SHIFT key the welding mode can be selected.

Choose between either “MANUAL" control, to manually input the parameters or "SYNERGIC/EASY", in which the device will set parameters partially by itself.

Water cooling attachments can be switched on via the welding device’s main power switch. Alternatively it can be operated independently from the welding device.

Shows the welding / cutting parameters.

The LED light indicates overheating or a malfunction.

The LED lights to indicate that the network connection of the phase has failed.